HPE Storage Users Group https://www.3parug.com/ |
|
Problem with add M6720 to V7200 https://www.3parug.com/viewtopic.php?f=18&t=1056 |
Page 1 of 1 |
Author: | supakijku [ Mon Dec 08, 2014 12:21 am ] |
Post subject: | Problem with add M6720 to V7200 |
Dear All I have a problem with adding a new shelf M6720 to 3Par v7200. My steps are 1. i connected v7200 DP1 to M6720 DP1 on both controller. The shelf firmware version shown unknown so i use command "upgradecage cage1" After command completed successfully 2. showcage -d cage0 no defail information available cage1 status is fine 3. there are some error said upgradepd failed in Event 4. i called and open case with HP Thailand, they the problem come from my incorrect cabling. 5. i reconnect cabling DP2 to DP1 but the problem is still presisted. 6. in 3par managaement console, there is no controller in controller menu but all volume are accesible fine. what i want to do next is disconnect cage1 and reboot cage0 or do you guys have any workaround solution? thank you in advance. my showcage -d shown below. Id Name LoopA Pos.A LoopB Pos.B Drives Temp RevA RevB Model Side 0 cage0 --- 1 --- 1 0 0-0 - - DCN1 n/a 1 cage1 1:0:2 0 0:0:2 0 6 0-0 320c 320c DCS1 n/a -----------Cage detail info for cage0 --------- Position: --- No detailed information available -----------Cage detail info for cage1 --------- Position: --- Interface Board Info Card0 Card1 Firmware_status Current Current Product_Rev 320c 320c State(self,partner) OK,OK OK,OK VendorId,ProductId HP,DCS1 HP,DCS1 Master_CPU Yes No SAS_Addr 50050CC117ECAD3E 50050CC117EBFFFE Link_Speed(DP1,DP2) 6.0Gbps,Unknown 6.0Gbps,Unknown PS PSState ACState DCState Fan State Fan0_Speed Fan1_Speed ps0 OK OK OK OK HiSpeed HiSpeed ps1 OK OK OK OK HiSpeed HiSpeed -------------Drive Info-------------- --PortA-- --PortB-- Drive DeviceName State Temp(C) LoopState LoopState 0:0 5000cca028b0220f Normal N/A OK OK 4:0 5000cca028b0250f Normal N/A OK OK 8:0 5000cca028b0070b Normal N/A OK OK 12:0 5000cca028b006f3 Normal N/A OK OK 16:0 5000cca028b00b6b Normal N/A OK OK 20:0 5000cca028b0064b Normal N/A OK OK |
Author: | RitonLaBevue [ Mon Dec 08, 2014 2:06 am ] |
Post subject: | Re: Problem with add M6720 to V7200 |
DP1 to DP1... sounds strange to me... Did you read any cabling guide ? what checkhealth said ? |
Author: | supakijku [ Thu Dec 11, 2014 2:33 am ] |
Post subject: | Re: Problem with add M6720 to V7200 |
Cabling is my mistake. I roughly read the document and unaware of DP port. check heatlh shown below. Checking alert Checking cabling Checking cage Checking date Checking ld Could not check ld: Error: Could not retrieve node informa Checking license Checking network Checking node Could not check node: Error: Could not retrieve node infor Checking pd Checking port Checking rc Checking snmp Checking task Checking vlun Checking vv Component ---------------Description--------------- Qty Cabling Missing Port 1 Cage Cages not on current firmware 1 Cage Cages missing A loop 1 Cage Cages missing B loop 1 Cage Degraded or failed cage power supply fans 2 Cage Degraded or failed cage power supplies 2 Cage Degraded or failed cage AC power 2 Could ld: 1 Could ld 1 License Licenses which have expired 1 Network Errors detected on network 1 Could node: 1 Could node 1 PD PD count exceeds licensed quantity 1 PD Cages with unbalanced disks 2 PD PD models missing from firmware database 6 PD PDs that are failed 6 vlun Paths not reported by host agent 2 |
Author: | RitonLaBevue [ Thu Dec 11, 2014 5:05 am ] |
Post subject: | Re: Problem with add M6720 to V7200 |
Now check the corresponding guide and correct your cabling. |
Author: | supakijku [ Fri Dec 12, 2014 12:50 pm ] |
Post subject: | Re: Problem with add M6720 to V7200 |
cabling is corrected now. according to cabling guide but the problem is still persist. What HP Thailand suggest me to do is only rebuild my cage0 after they review my splore log but i think there might there might be some way to solve this issue without rebuild my cage0. i'm in the process of backup everything and i'll try to reboot cage0 today. After reboot cage0 status back to normal. but upgradepd task still running and failed |
Page 1 of 1 | All times are UTC - 5 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |