HPE Storage Users Group https://www.3parug.com/ |
|
SSMC Customer Feedback https://www.3parug.com/viewtopic.php?f=18&t=1288 |
Page 20 of 25 |
Author: | drunkmet [ Wed Jul 19, 2017 3:41 pm ] |
Post subject: | Re: SSMC Customer Feedback |
has anyone had success getting the web interface for SSMC 3.1 to run on port 443? we are using the linux version and followed the steps on page 17 of the admin guide here: http://h20566.www2.hpe.com/hpsc/doc/pub ... 06232en_us but the web interface doesn't come back up after a service start (on 443 or 8443) |
Author: | SergioQC [ Wed Jul 26, 2017 7:51 am ] |
Post subject: | Re: SSMC Customer Feedback |
SSMC 3.1 it would be interesting to be able to compare two systems with a scheduled report in the same way as can be done for on-demand reports. Once the report is created and scheduled, the comparison selection is not respected. Thanks |
Author: | wbbouldin [ Wed Jul 26, 2017 9:34 am ] |
Post subject: | Re: SSMC Customer Feedback |
SergioQC wrote: Once the report is created and scheduled, the comparison selection is not respected. Right, and this will be changed in SSMC 3.2 so the other system will be displayed in the scheduled report too.
|
Author: | Reactor [ Thu Aug 03, 2017 10:29 am ] |
Post subject: | Re: SSMC Customer Feedback |
I just found that SSMC 3.2 has been posted to HPE's Software Updates portal and available for download. As of this writing, though, SSMC 3.1 is still listed as the version available via Software Depot. |
Author: | mkaaden [ Thu Aug 24, 2017 6:14 am ] |
Post subject: | Re: SSMC Customer Feedback |
This week we updated our Lab InServ from 3.2.2 to 3.3.1 EGA Before update we completely cleaned up the array. After 3.3.1, I setup vvol's again for testing and moved a VM to the 3PAR. Before the update, SSMC showed the VM's which were provisioned with vvols on the Container But now after the upgrade and vmotion, Storage Container in SSMC say's it conains 2(?) VM's, but when click on it, no VM's are shown. It also say's it contains 5 vvols, however after clicking on it ... nothing. However from the CLI: Doing a showvolsc it shows the container containing 2 VM's en 5 vvols Doing a showvolvm -sc <container_name> it show the VM I moved containing 4 vvols. I already created a new Storage Container and vmotioned the VM to it: still the same. I also noticed that the state for both containers say's: Unknown Just installed 3.2 in our Lab, still the same issue with the Containers and VM's |
Author: | wbbouldin [ Thu Aug 24, 2017 9:50 am ] |
Post subject: | Re: SSMC Customer Feedback |
mkaaden wrote: But now after the upgrade and vmotion, Storage Container in SSMC say's it conains 2(?) VM's, but when click on it, no VM's are shown. That doesn't sound right. If you could, please open a support case so they can collect the logs and we can get this figured out.
It also say's it contains 5 vvols, however after clicking on it ... nothing. |
Author: | mkaaden [ Thu Aug 24, 2017 11:31 am ] |
Post subject: | Re: SSMC Customer Feedback |
Hi Brian, This 3PAR is out of support, hence we performed the upgrade to 3.3.1 Is it still possible then to open a case on a Inserv that has no Support ? Does it make any difference whether we de a compleet reinstall of SSMC before we contact support at all ? Regards, Martijn |
Author: | wbbouldin [ Thu Aug 24, 2017 12:04 pm ] |
Post subject: | Re: SSMC Customer Feedback |
mkaaden wrote: Does it make any difference whether we de a compleet reinstall of SSMC before we contact support at all ? It shouldn't matter but it's worth a try. I'll follow up with you in a PM to see what we can do to find out what's causing SSMC to not display the VVOL info.
|
Author: | cali [ Tue Sep 12, 2017 8:00 am ] |
Post subject: | Re: SSMC Customer Feedback |
Have seen an Issue on 4 Systems (at 2 Sites) after Update to 3.3.1. On all 3PARs after the Update the SSMC 3.2 shows "0 Ports" in Systems. Remove and add the Arrays in SSMC fix it. @wbbouldin Have you try to remove and add the Storage? May be it fix it for you to. |
Author: | wbbouldin [ Tue Sep 12, 2017 11:11 am ] |
Post subject: | Re: SSMC Customer Feedback |
cali wrote: On all 3PARs after the Update the SSMC 3.2 shows "0 Ports" in Systems. Just to make sure I understand the order of events, you updated SSMC to version 3.2 and then updated the 3PAR OS to 3.3.1, right? From what version of the 3PAR OS did you update?
Remove and add the Arrays in SSMC fix it. |
Page 20 of 25 | All times are UTC - 5 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |